Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Panel Replacement Cost in Bedford Park?
Panel replacement in Bedford Park typically costs $250 – $500 for a single section, and most jobs land in that range once the old panel is off and the new one is fitted. That’s the estimate for the panel itself plus labor. If the damage runs across two sections, expect closer to the top of the range or a bit above it. The written estimate you get before any work starts is the price that holds.
Garage door panels take a beating in this part of the Bronx. Between the tight driveways off streets like Perry Avenue and the way doors get nudged by cars backing out on Bedford Park Boulevard, dented and cracked sections are one of the most common calls we get. A single panel swap is usually a same-day job. Call (866) 850-5634 and we’ll get you a free estimate.
Key Takeaways
- Single panel replacement in Bedford Park: $250 – $500 typical.
- Two or more panels usually pushes the job above the single-panel range.
- Matching the panel to your existing door is the biggest variable in the price.
- We service LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor doors and openers, so we can source the right section.
- Free estimates, and the written quote sets the final price.
Panel Replacement Cost Breakdown (2026)
Here’s how the numbers usually shake out for a Bedford Park panel job. Every figure below is a typical estimated range for the local market, not a quote. Your actual price depends on the door and the section.
| Item | Typical Estimated Range |
|---|---|
| Single panel replacement (panel + labor) | $250 – $500 |
| Two panels replaced together | $450 – $850 |
| Bottom section with weather seal | $300 – $550 |
| Panel plus track realignment, when the impact bent the track | $370 – $740 |
| Roller replacement done alongside a panel swap | $110 – $220 |
| Cable repair if a panel impact also damaged a cable | $130 – $250 |
| Opener repair if the door stopped working after the damage | $120 – $320 |
What pushes a panel job toward the top of the range? Matching the section. A builder-grade door with a common profile is straightforward. A premium Clopay or Amarr section with a specific embossment, window insert or color takes more effort to match, and a discontinued profile may mean replacing the whole door instead. Labor climbs when the door is off-track, when the section is a bottom panel with an integrated seal, or when the surrounding panels also need to come down to get the new one in. What keeps it lower: a single plain section, a door that’s still running straight, and hardware that doesn’t need replacing.
What Affects Panel Replacement Pricing in Bedford Park
- Panel profile and manufacturer. Doors from Clopay, Amarr, Wayne Dalton, Raynor, and Craftsman all use different panel profiles and dimensions. A section that matches an in-stock profile costs less than one that has to be ordered or custom-matched. We carry brand-specific knowledge, so we’re not guessing at what fits.
- Single vs. multiple panels. One dented section is the low end. Damage that spans two or three panels pushes the price up fast, since each section is its own part and its own fitting time.
- Whether the track and hardware survived. A car bumper or a hard shove often bends the track as well as the panel. If the door won’t run straight, the track has to come back into line before the new section goes in.
- Cable and spring condition. Panels are heavy, and pulling one out and putting a new one in puts load on the cables. If a cable is frayed, we’ll flag it. Cables and springs are high-tension parts, and that work belongs with a trained technician, not a general handyman.
- Age and availability of your door model. A door that’s been on the wall for a long time may have a discontinued profile. In that case, matching the panel isn’t always possible, and we’ll tell you honestly when a full replacement makes more sense.
- Weather seal and trim. Bedford Park winters are cold and wet, and the bottom seal takes the worst of it. A bottom panel replacement usually includes a fresh seal, which adds a little to the cost but keeps the door closing tight against drafts.
How to Save on Panel Replacement
The single biggest lever is fixing the panel before the damage spreads. A small dent that’s ignored often turns into a bent section and a misaligned door, and that’s when a $250 job turns into something bigger. Get it looked at early.
- Match the profile, not the color. If your door’s color is discontinued, a close-match profile still fits and costs less than a custom color order. Ask what’s available before you commit.
- Handle the seal at the same time. Replacing a bottom panel is the natural moment to put on a fresh weather seal. Doing both in one visit saves a second trip and separate costs.
- Ask whether repair beats replacement. Sometimes a panel can be straightened or re-hung rather than replaced. We’ll give you the honest answer, not the upsell.
- Get the estimate in writing. A written estimate is free and it’s what the final price is set against. Call (866) 850-5634 for yours.
FAQs – Panel Replacement Cost
How much does one garage door panel cost to replace in Bedford Park?
One panel typically runs $250 – $500 in Bedford Park, panel and labor included. The exact figure depends on the profile, the manufacturer, and whether the track needs a small adjustment. Call (866) 850-5634 for a free estimate on your door.
Is it cheaper to replace one panel or the whole door?
One panel is almost always cheaper than a whole door, which starts at $700 and runs to $2,200 for a full installation. Replacing the entire door only makes sense when the bad section can’t be matched or when several panels are damaged. If you’re weighing it up, a free estimate will tell you which way the numbers fall.
Why does the bottom panel cost more than a middle panel?
The bottom section usually adds $50 or so because it carries the weather seal and takes the most impact, so it’s the most heavily built section on the door. It’s also the one most exposed to road splash and cold through a Bedford Park winter, which is why it’s the panel we replace most often.
Do you match my existing door’s brand and color?
We work with Clopay, Amarr, Wayne Dalton, Raynor, Craftsman, LiftMaster, Chamberlain, and Genie equipment, and we match the panel to your existing door wherever the profile is still available. When it isn’t, we’ll say so up front and offer the closest fit or a full replacement, whichever makes more sense for your door.
Can you come the same day if my panel is damaged?
Same-day service is often possible for panel work, and we treat a door that won’t close as the priority it is. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Call (866) 850-5634 and we’ll book you in.
If a section is dented, cracked, or letting the weather in, don’t leave it. A matched panel fitted properly keeps the whole door running true, and it costs far less than waiting for the damage to spread. We offer free estimates, and the written quote is the price. Call (866) 850-5634. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Garage Door Repair Bedford Park.
Pricing reflects the Bedford Park market as of 2026. Garage Door Repair Bedford Park offers free estimates – call (866) 850-5634.
What Our Customers Say
"Opener works, remotes are programmed, no complaints on the work. Took three days to get on the schedule though, so if you've got a car trapped inside, say so when you call."
- Kurt Gallagher"Logic board on a 15 year old opener. He was upfront that a new opener would cost less than the board plus labor, and he wasn't wrong. No pressure either way."
- Andre Carter"The old chain drive sounded like a freight train through the bedroom above the garage. Went with the belt drive they recommended and now I genuinely cannot hear it open from upstairs."
- Javier Salazar